THE ART OF BASIC PLUMBING FOR INSTALLING A BATHTUB

The Art of Basic Plumbing for Installing a Bathtub

The Art of Basic Plumbing for Installing a Bathtub

Blog Article

Automated Marketing

We have noticed the article about Installing A Bathtub directly below on the web and felt it made perfect sense to share it with you on my blog.


A Step-by-Step Guide to Installing a Bathtub
Installing a tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old bath tub with a new one is also a moderately hard job. If the old bathtub is easily accessible, the task can relocate easily; if you have to open up a wall to get rid of the old bathtub as well as position the new tub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and also embeded in the new one. Ensure you have actually qualified on your own for the job and are comfortable attempting it. As opposed to working with a professional to take over a halfway-completed project, it is far better to take into consideration using one before you begin. Chances are you might need a specialist plumber to make tube connections.
This short article will aid you set up a brand-new tub in your bathroom if you have already gotten a new tub as well as don't require to transform the setup of your previous supply of water pipelines.
Your tools as well as product checklist must consist of the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Preparing for the Setup


    Firstly, the supporting structure supplied with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
    Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
    Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its final position.

    Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be rather bothersome due to the restricted access that is often the case.
    Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
    Prior to going on to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

    Mounting the Tub


    Making use of the two wood boards under its feet, place the tub in the called for position. The wooden boards are useful in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
    The next objective is to ensure that the tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the tub until the level reads level.
    To set up faucets, fit the bottom of the outermost adaptable tap connector to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
    Turn on the water system as well as check all joints and also new pipework for leaks as well as tighten them if required. Fill the bath tub and likewise check the overflow electrical outlet and the typical electrical outlet for leaks.
    Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bath tub ought to wait up until the tub has actually been made use of at least when as this will resolve it right into its last position.

    Fitting New Touches


    If the tails of the new taps are plastic, then you will require a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end provides a connection to the existent supply pipelines.
    If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, position the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and the sink. Safeguard the tap in place with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap adapters. The former type should be attached to the tap finishes first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Bath tub


    In the location where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, creating the water to permeate the wall in between the bath and also the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
    You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealant can crack relatively very early if you do not consider this motion before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily offered on the market. It is recommended to fit the tiles using waterproof or water resistant adhesive and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    Do you really like reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave a review directly below. We'd be glad to find out your ideas about this write-up. We are looking forward to see you back again before long. I beg you set aside a second to promote this article if you liked it. Thank you for your time. Kindly check up our website back soon.


    Top service? Dial now.

    Report this page